Dynacon 150

Dynacon 150 underfloor heating circuit manifold

Connection kit 3 with Zeparo Vent air separator in supply and Zeparo Dirt sludge separator in return, DN 20

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Thermometer for Globo

to replace by changing the closing cap.
Temperatur range from 0 °C to 120 °C.

S-connection

For connection kit 3. Installation aid for return in manifold boxes.

Connection kit with ball valves, angle connection, including spacer for heat meter in return. Ball valves with connection M10x1 for direct measurement in supply and return.

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Connection kit 1 with Globo ball valves, DN 20

with red end cap in supply and blue end cap in return.

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Manifold boxes

Flush-mounted box, installation depth 110 - 150 mm.
Note the minimum installation depth 125 mm for connection set 5!

Extension kit

Connection kit 2 with STAD balancing valve and Globo ball valve, DN 20

including measuring nipple for measuring differential pressure and flow rate.

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Connection kit with ball valves, straight connection, including spacer for heat meter in return. Ball valves with connection M10x1 for direct measurement in supply and return.

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Connection kit 5, fixed value control station

with high-efficiency pump Grundfos Alpha 2 15 - 60 130, thermostatic valve with contact sensor and electrical pipe contact safety switch 230V, 15A.
Minimum installation depth manifold boxes: 125 mm.

Connection kit 4 with Globo ball valve DN 20, including spacer for heat meter in return

Globo ball valve with connection G1/4 for direct measurement in supply and return.

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Connection kit 4 can be mounted vertically using appropriate 1" elbows (not included in delivery). Manifold box sizes are then selected according to connection kit 1.

Thermostatic mixing valve for radiant heating

Pump connection with ball valve
Temperature 25 - 55 °C

*) 130 mm pump + 2x2 mm gasket

Kvs = m³/h at a pressure drop of 1 bar and fully open valve.

Room transmitter

battery-driven electronic Fuzzy controller, including battery.

Replacement thermostatic insert

with automatic flow limiter for Dynacon 150.

Compression fitting

for copper or precision steel pipe according to DIN EN 1057/10305-1/2 and stainless steel pipe.
Connection male thread G3/4 according to DIN EN 16313 (Eurocone).
Soft sealed, max. 95°C.
Nickel-plated brass.

Distributor strip

This unit is used for wiring thermostats and electro-thermal actuators. The unit is suitable for underfloor heating and cooling (summer/winter operation). It is possible to switch over between heating and cooling via an external signal. The pump logic enables enery-optimised pump control. For up to 6 zones (rooms). Ready to plug in to a 230 V power socket.

Thermostatic head F

Remote dial with built-in sensor. Liquid filled sensor.
Setting range 0 °C to 27 °C.

Support sleeve

for copper or precision steel pipe with a 1 mm wall thickness.
Brass.

Setting key

for Eclipse. Color orange.

Double connection fitting

For clamping plastic, copper, precision steel or multi-layer pipes.
Brass, nickel-plated.

Length adjustment fitting

For connecting to plastic, copper, precision steel or multi-layer pipes.
For valves with male thread connection G3/4.
Brass nickel-plated.

Thermostat P with digital switch clock

electronic two-point room thermostat for time-dependent control of the room temperature, with digital automatic timer, pulse-width modulation output signal (PWM) and floating change-over contact. Menu-driven via four buttons.

Double nipple

Both sides for clamping plastic, copper, precision steel or multi-layer pipes.
Brass nickel-plated.

Central unit

Receives the room transmitters radio signals. With 8 or 6 output channels for the connection of the thermal actuators.

Replacement filling, draining, flushing and venting device 1/2”

Compression fitting

for plastic pipe according to DIN 4726, ISO 10508. PE-X: DIN 16892/16893, EN ISO 15875; PB: DIN 16968/16969.
Connection male thread G3/4 according to DIN EN 16313 (Eurocone).
Nickel-plated brass.

Room thermostat

with thermal recirculation, controls the room temperature in connection with thermal actuators.

Compression fitting

for Alu/PEX multi-layer pipe according to DIN 16836.
Connection male thread G3/4 according to DIN EN 16313 (Eurocone).
Nickel-plated brass.

Compression fitting

for copper or precision steel pipe according to DIN EN 1057/10305-1/2.
Connection male thread G3/4 according to DIN EN 16313 (Eurocone).
Metal-to-metal joint.
Nickel-plated brass.
With a pipe wall thickness of 0.8-1 mm insert supporting sleeves. Heed pipe manufacturer’s technical advice.

Thermostat P with analog switch clock

electronic two-point room thermostat for time-dependent control of the room temperature, with analog 7-day automatic timer, pulse-width modulation output signal (PWM) and floating change-over contact.

EMOtec

Two-point thermal actuator for floor heating systems. With position indicator in NC version. Suitable for all Heimeier thermostatic valve bodies. For technical data, please refer to the EMOtec datasheet.

Handwheel

for all HEIMEIER thermostatic valve bodies. With direct connection, white.